[hobbit] UPS monitoring using devmon
David Baldwin
david.baldwin at ausport.gov.au
Mon Sep 14 08:41:01 CEST 2009
thorsten.erdmann at daimler.com wrote:
>
> Hi David
>
> I just tested your template against my MGE Galaxy. There are some
> minor issues:
>
I developed it against a Chloride UPS.
> 1. battery voltage is displayed as 42100V, yeah. I solved that with
> setting the transform of "upsBatteryVoltageTxt" to
> "{upsBatteryVoltage} / 10" instead of "x 10"
Whoops - my bad. My UPS shows:
UPS-MIB::upsBatteryVoltage.0 (.1.3.6.1.2.1.33.1.2.5.0) = INTEGER: 22 0.1
Volt DC
So that's really 2.2V not 220V.
> 2. battery current is 0A, it seems that the MGE does not deliver this
> value
Likewise, my UPS does not return anything other than 0. We just had a
power failure and it didn't even move from 0 during that, so it's not
drain on the batteries when in use. It was really there for completeness.
> 3. message test is yellow: "primary OID upsAlarmDescrTxt in table is
> a non-repeater", I don't know how to solve that
Rest assured, when there IS an alarm, you will see them - I had 2 this
morning.
At the moment devmon doesn't handle empty repeaters well. I had some
discussions with Buchan a while ago.
> 4. output power is 0kW. If I use the special MGE MIB I get real results
I do get real values on output power (but not on input power).
> 5. input power displays unrealistic results:
> Line bads: 3
> Input configuration: 3 lines of 0 V AC @ 0.0 Hz
>
These depend on config values. They may need to be populated in the UPS
management interface - I'm not sure. I do get them returned for my UPS.
> UPS Input
> Phase Freq Volts Amps Power
> 1 50.0 Hz 390V 28.0A 2746W
> 2 50.0 Hz 395V 28.0A 2835W
> 3 50.0 Hz 391V 28.0A 2765W
> 6. I am missing some temperature tests
>
> So now I am unsure what to do.
> I can ignore these issues
> I can modify your template to use the OIDs of the vendor's MIB
> I can use my own template which does not display so much results, but
> uses the vendor's MIB
>
I've had similar dilemmas with HP servers with all kinds of mixes of
hardware RAID controllers, hardware event logs and then adding
SNMP-Informant on the top.
> It seems that the vendors does not support the standard UPS MIB very
> cleanly. So I think we have to build a special template for every
> vendor. :-(
>
> But even if I don't use your template it was very helpful. It is a
> very good demonstration how to use tables and other stuff in devmon. I
> didn't try the graphing now, but I will do it now. :-)
>
Let me know how you go with that.
> Thank you for your work!!!
>
Thanks.
I just added "templatebuilder.pl" into the extras directory in the
devmon SVN repository.
It gives a good start on putting together a template, translating
between names and OIDs, generating barebones oids, transforms and
thresholds files.
It relies on having the MIB definition files installed correctly.
David.
> Thorsten
>
> david.baldwin at ausport.gov.au schrieb am 11.09.2009 07:26:30:
>
> > My UPS template has been tweaked and is now available from the devmon SF
> > repository:
> > http://devmon.svn.sourceforge.net/viewvc/devmon/trunk/templates/ups.
> > tar.gz?view=tar
> >
> > README file includes hobbitgraph.cfg section and info on setting up RRD
> > collection and graphing.
> >
> > Let me know if any problems. The msgs test attempts to show the
> > AlarmDesc repeater which is empty unless there are any alarms which may
> > cause issues - I've increased the number of "not found" repeaters
> > slightly in my copy of devmon to be more lenient. The line is in
> > modules/dm_snmp.pm
> >
> > if($failed_query > 2) {
> >
> > I increased 2 to 6.
> >
> >
> > >
> > > your example was very helpfull. I now managed to get a working devmon
> > > template for my MGE UPS. Only graphing isn't working now.
> > >
> > > BTW.: anyone knows how I can format output numbers in devmon. I now
> > > get the voltages with two digits behind the colon, but these are
> > > always zero. So I want to omit these digits at all.
> > >
> > The number of decimal digits displayed is controlled in the transforms
> > file with MATH operator by adding ": N" - e.g.
> >
> > upsInputCurrentA : MATH : {upsInputCurrent} / 10 : 1
> >
> > will display for example 10.1 - change to ": 0" to get 10
> >
> > David.
> > >
> > > Thorsten Erdmann
> > >
> > >
> > > david.baldwin at ausport.gov.au schrieb am 10.09.2009 09:51:49:
> > >
> > > > Sorry all, didn't get time today to update the UPS template today.
> > > >
> > > > It has separate graphs for input voltage, output phase voltages,
> battery
> > > > levels and separate tests/alerting on various conditions - input
> > > > voltage=0, battery time remaining <15 mins, output phase
> overload, etc.
> > > >
> > > > David.
> > > > > Oops, forgot to add the graphing bit.
> > > > >
> > > > > Usual stuff.
> > > > > In hobbitserver.cfg
> > > > > Add "ups=ncv" to TEST2RRD=
> > > > > Add "ups" to GRAPHS=
> > > > > Add line NCV_ups="Load:GAUGE,Charge:GAUGE"
> > > > >
> > > > > Add this to hobbitgraph.cfg
> > > > > [ups]
> > > > > TITLE UPS Charge
> > > > > YAXIS Power
> > > > > -u 100
> > > > > -l 0
> > > > > DEF:u=ups.rrd:Charge:AVERAGE
> > > > > DEF:p=ups.rrd:Load:AVERAGE
> > > > > LINE2:u#00CC00:Charge
> > > > > LINE2:p#0000FF:Load
> > > > > COMMENT:\n
> > > > > GPRINT:u:LAST:Charge \: %5.1lf%s (cur)
> > > > > GPRINT:u:MAX: \: %5.1lf%s (max)
> > > > > GPRINT:u:MIN: \: %5.1lf%s (min)
> > > > > GPRINT:u:AVERAGE: \: %5.1lf%s (avg)\n
> > > > > GPRINT:p:LAST:Load \: %5.1lf%s (cur)
> > > > > GPRINT:p:MAX: \: %5.1lf%s (max)
> > > > > GPRINT:p:MIN: \: %5.1lf%s (min)
> > > > > GPRINT:p:AVERAGE: \: %5.1lf%s (avg)\n
> > > > > Cheers
> > > > > Vernon
> > > > >
> > > > >
> > > > >
> > > > >
> > >
> ------------------------------------------------------------------------
> > > > > *From:* Everett, Vernon [mailto:Vernon.Everett at woodside.com.au]
> > > > > *Sent:* Thursday, 10 September 2009 2:50 PM
> > > > > *To:* 'hobbit at hswn.dk'
> > > > > *Subject:* RE: [hobbit] Antwort: RE: [hobbit] UPS monitoring using
> > > devmon
> > > > >
> > > > > I wrote this a while back for our MGEs.
> > > > > As you can see, it predates my introduction to devmon and
> indicates a
> > > > > complete lack of understanding of SNMP.
> > > > > That being said, the code and the MIBs might give you a good
> > > > > indication of where to start.
> > > > > (Either that, or you can just use it as "good enough")
> > > > > This was designed to run on the hobbit/xymon server.
> > > > >
> > > > > I have been meaning to rewrite this, or move it to devmon, but
> just
> > > > > haven't had the time.
> > > > > (And it's doing an adequate job for now.)
> > > > >
> > > > > Cheers
> > > > > V
> > > > >
> > > > > bb-host entries look like this
> > > > > 1.2.3.4 galaxy3000 # http://1.2.3.4/ups_prop.htm ups
> galaxy3000
> > > > > COMMENT:"Meaningful Comment if required"
> > > > > 2.3.4.5 Karratha_UPS # http://2.3.4.5/ups_prop.htm ups
> galaxy3000
> > > > > COMMENT:"Insert Comment"
> > > > >
> > > > >
> > > > >
> > > > >
> > > > > --- snip---
> > > > >
> > > > > cat ups.ksh
> > > > > #!/bin/ksh
> > > > > DATE=$(date)
> > > > > #set -x
> > > > > SPACER="
> > >
> > > > > "
> > > > > BBTMP=/tmp
> > > > > #BBHOSTS=/etc/hobbit/bb-hosts
> > > > > #OUT=$BBTMP/upspage
> > > > > BBHOSTLIST="$BBHOSTS $(grep ^include $BBHOSTS | awk '{ print
> $2 }')" #
> > > > > Make sure we read the include files too
> > > > > #grep -h " ups " $BBHOSTLIST | egrep -v "^page|^include"
> > > > > grep -h " ups " $BBHOSTLIST | egrep -v "^page|^include" |
> while read
> > > > > IP UPSNAME HASH URL UPS TYPE OTHER
> > > > > do
> > > > > echo $IP $UPSNAME
> > > > > ping -c1 $IP > /dev/null
> > > > > if [ $? -eq 0 ]
> > > > > then
> > > > > COLOUR=green
> > > > > case $TYPE in
> > > > > galaxy3000)
> > > > > > $OUT.warn
> > > > > > $OUT.tmp
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > SNMPv2-SMI::mib-2.33.1.1.1.0)
> > > > > DEVICE=${TEMP##*:} # String
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > SNMPv2-SMI::mib-2.33.1.1.2.0)
> > > > > MODEL=${TEMP##*:} # String
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > SNMPv2-MIB::sysLocation.0)
> > > > > LOCATION=${TEMP##*:} # String
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > SNMPv2-SMI::mib-2.33.1.1.4.0)
> > > > > SERIAL=${TEMP##*:} # String
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.4.8.0)
> > > > > LOWBATTERY=${TEMP##*:} # Integer % Point at
> > > > > which shutdown triggered
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.5.1.0)
> > > > > TIME_REMAIN=${TEMP##*:} # Integer seconds
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.5.2.0)
> > > > > BATTERY_LEVEL=${TEMP##*:} # Integer %
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.5.9.0)
> > > > > BATTERY_FAULT=${TEMP##*:} # Integer 1=yes 2=no
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.5.11.0)
> > > > > BATTERY_REPLACE=${TEMP##*:} # Integer 1=yes 2=no
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.5.15.0)
> > > > > CHARGER_FAULT=${TEMP##*:} # Integer 1=yes 2=no
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.7.3.0)
> > > > > OUT_ON_BAT=${TEMP##*:} # Integer 1=yes 2=no
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.7.4.0)
> > > > > OUT_ON_BYPASS=${TEMP##*:} # Integer 1=yes 2=no
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.7.10.0)
> > > > > OUT_OVERLOAD=${TEMP##*:} # Integer 1=yes 2=no
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.7.10.0)
> > > > > COMMSOK=${TEMP##*:} # Integer 1=yes 2=no
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.6.1.0)
> > > > > INPHASES=${TEMP##*:} # Integer 1 or 3
> > > > >
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > 1.3.6.1.4.1.705.1.6.2.1.2)
> > > > > INVOLT=${TEMP##*:} # Integer 10ths of a volt
> > > > >
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > 1.3.6.1.4.1.705.1.6.2.1.3)
> > > > > INFREQ=${TEMP##*:} # Integer 10ths of a Hertz
> > > > >
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > 1.3.6.1.4.1.705.1.6.2.1.6)
> > > > > INAMPS=${TEMP##*:} # Integer 10ths of an Amp
> > > > >
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.6.3.0)
> > > > > INOK=${TEMP##*:} # Integer 1=yes 2=no
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.6.4.0)
> > > > > INFAILCAUSE=${TEMP##*:} # Integer 1=no fault
> > > > > # 2=bad voltage
> > > > > # 3=bad frequency
> > > > > # 4=no voltage
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.7.1.0)
> > > > > OUTPHASES=${TEMP##*:} # Integer 1 or 3
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > 1.3.6.1.4.1.705.1.7.2.1.2)
> > > > > OUTVOLT=${TEMP##*:} # Integer 10ths of a volt
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > 1.3.6.1.4.1.705.1.7.2.1.3)
> > > > > OUTFREQ=${TEMP##*:} # Integer 10ths of a Hertz
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > 1.3.6.1.4.1.705.1.7.2.1.4)
> > > > > OUTLOAD=${TEMP##*:} # Integer %
> > > > > TEMP=$(snmpget -v1 -c public $IP
> > > 1.3.6.1.4.1.705.1.7.2.1.5)
> > > > > OUTAMPS=${TEMP##*:} # Integer 10ths of an Amp
> > > > > TEMP=$(snmpget -v1 -c public $IP
> 1.3.6.1.4.1.705.1.7.11.0)
> > > > > OVERTEMP=${TEMP##*:} # Integer 1=yes 2=no
> > > > > echo "Manufacturer
> "$DEVICE | sed
> > > > > 's/"//g' >> $OUT.tmp
> > > > > echo "Model "$MODEL
> | sed
> > > > > 's/"//g' >> $OUT.tmp
> > > > > echo "Serial Number
> "$SERIAL | sed
> > > > > 's/"//g' >> $OUT.tmp
> > > > > echo "Location
> "$LOCATION |
> > > > > sed 's/"//g' >> $OUT.tmp
> > > > > echo >> $OUT.tmp
> > > > > #$LOWBATTERY
> > > > > #WARN=""
> > > > > #[ -z "$TIME_REMAIN" ] && TIME_REMAIN=0
> > > > > #[ $TIME_REMAIN -lt 1200 -a "$COLOUR" != "red" ] &&
> > > > > COLOUR=yellow
> > > > > #[ $TIME_REMAIN -lt 1200 ] && WARN="Time Remaining
> low"
> > > > > #[ $TIME_REMAIN -lt 600 ] && COLOUR=red
> > > > > #[ $TIME_REMAIN -lt 600 ] && WARN="Time Remaining
> > > critical"
> > > > > #[ "$WARN" != "" ] && echo $WARN >> $OUT.warn
> > > > > ((s=$TIME_REMAIN%60))
> > > > > ((m=$TIME_REMAIN/60))
> > > > > echo "Time Remaining "$m
> Minutes $s
> > > > > Seconds >> $OUT.tmp
> > > > > WARN=""
> > > > > [ -z "$BATTERY_LEVEL" ] && BATTERY_LEVEL=0
> > > > > [ $BATTERY_LEVEL -lt 95 -a "$COLOUR" != "red" ] &&
> > > > > COLOUR=yellow
> > > > > [ $BATTERY_LEVEL -lt 95 ] && WARN="Battery level low"
> > > > > [ $BATTERY_LEVEL -lt 50 ] && COLOUR=red
> > > > > [ $BATTERY_LEVEL -lt 50 ] && WARN="Battery level
> critical"
> > > > > [ "$WARN" != "" ] && echo $WARN >> $OUT.warn
> > > > > echo "Battery Level
> "$BATTERY_LEVEL
> > > > > % >> $OUT.tmp
> > > > > BATTERY_LEVEL=$(echo $BATTERY_LEVEL | sed 's/[
> \t]*//')
> > > > > if [ $BATTERY_FAULT -eq 1 ]
> > > > > then
> > > > > BF=Yes
> > > > > COLOUR=red
> > > > > echo "Battery Fault!" >> $OUT.warn
> > > > > else
> > > > > BF=No
> > > > > fi
> > > > > echo "Battery Fault "$BF >>
> > > $OUT.tmp
> > > > > if [ $BATTERY_REPLACE -eq 1 ]
> > > > > then
> > > > > BR=Yes
> > > > > COLOUR=red
> > > > > echo "Battery replacement required" >> $OUT.warn
> > > > > else
> > > > > BR=No
> > > > > fi
> > > > > echo "Replace Battery "$BR >>
> > > $OUT.tmp
> > > > > if [ $BATTERY_FAULT -eq 1 ]
> > > > > then
> > > > > BR=Yes
> > > > > COLOUR=red
> > > > > echo "Battery replacement required" >> $OUT.warn
> > > > > else
> > > > > BR=No
> > > > > fi
> > > > > if [ $CHARGER_FAULT -eq 1 ]
> > > > > then
> > > > > CF=Yes
> > > > > COLOUR=red
> > > > > echo "Charger Fault" >> $OUT.warn
> > > > > else
> > > > > CF=No
> > > > > fi
> > > > > echo "Charger Fault "$CF >>
> > > $OUT.tmp
> > > > > if [ $OUT_ON_BAT -eq 1 ]
> > > > > then
> > > > > OUT_ON_BAT=Yes
> > > > > COLOUR=red
> > > > > echo "UPS running on battery" >> $OUT.warn
> > > > > else
> > > > > OUT_ON_BAT=No
> > > > > fi
> > > > > echo "On Battery
> "$OUT_ON_BAT
> > > > > >> $OUT.tmp
> > > > > if [ $OUT_ON_BYPASS -eq 1 ]
> > > > > then
> > > > > OUT_ON_BYPASS=Yes
> > > > > COLOUR=red
> > > > > echo "UPS on power bypass" >> $OUT.warn
> > > > > else
> > > > > OUT_ON_BYPASS=No
> > > > > fi
> > > > > echo "On Bypass
> > > > > "$OUT_ON_BYPASS >> $OUT.tmp
> > > > > if [ $OUT_OVERLOAD -eq 1 ]
> > > > > then
> > > > > OUT_OVERLOAD=Yes
> > > > > COLOUR=red
> > > > > echo "UPS output overload" >> $OUT.warn
> > > > > else
> > > > > OUT_OVERLOAD=No
> > > > > fi
> > > > > echo "Battery Overload
> "$OUT_OVERLOAD
> > > > > >> $OUT.tmp
> > > > > if [ $OVERTEMP -eq 1 ]
> > > > > then
> > > > > OVERTEMP=Yes
> > > > > COLOUR=red
> > > > > echo "Unit overheating" >> $OUT.warn
> > > > > else
> > > > > OVERTEMP=No
> > > > > fi
> > > > > echo "Unit Overheating
> "$OVERTEMP >>
> > > > > $OUT.tmp
> > > > > #if [ $COMMSOK -eq 2 ]
> > > > > #then
> > > > > # COMMSOK=No
> > > > > # COLOUR=red
> > > > > # echo "No comms from device" >> $OUT.warn
> > > > > #else
> > > > > # COMMSOK=Yes
> > > > > #fi
> > > > > #echo "Comms OK
> "$COMMSOK >>
> > > > > $OUT.tmp
> > > > > echo >> $OUT.tmp
> > > > > echo "Input Phases
> "$INPHASES >>
> > > > > $OUT.tmp
> > > > > INVOLT=$(echo "scale=1 ; $INVOLT/10" | bc)
> > > > > echo "Input Voltage
> "$INVOLT >>
> > > > > $OUT.tmp
> > > > > INFREQ=$(echo "scale=1 ; $INFREQ/10" | bc)
> > > > > echo "Input Frequency
> "$INFREQ >>
> > > > > $OUT.tmp
> > > > > INAMPS=$(echo "scale=1 ; $INAMPS/10" | bc)
> > > > > echo "Input Current
> "$INAMPS >>
> > > > > $OUT.tmp
> > > > > if [ $INOK -eq 1 ]
> > > > > then
> > > > > # A silly case of reverse logic applies here
> > > > > INOK=No
> > > > > COLOUR=red
> > > > > echo "Power input outside tollerance" >> $OUT.warn
> > > > > else
> > > > > INOK=Yes
> > > > > fi
> > > > > echo "Input OK "$INOK >>
> > > $OUT.tmp
> > > > > [ $INFAILCAUSE -eq 1 ] && FAILCAUSE="No failures"
> > > > > [ $INFAILCAUSE -eq 2 ] && FAILCAUSE="Voltage out of
> > > > > tollearance"
> > > > > [ $INFAILCAUSE -eq 3 ] && FAILCAUSE="Frequency out of
> > > > > tollernace"
> > > > > [ $INFAILCAUSE -eq 4 ] && FAILCAUSE="No voltage -
> > > power fail"
> > > > > echo "Cause of Failure
> "$FAILCAUSE >>
> > > > > $OUT.tmp
> > > > > echo >> $OUT.tmp
> > > > > echo "Output Phases
> "$OUTPHASES >>
> > > > > $OUT.tmp
> > > > > OUTVOLT=$(echo "scale=1 ; $OUTVOLT/10" | bc)
> > > > > echo "Output Voltage
> "$OUTVOLT >>
> > > > > $OUT.tmp
> > > > > OUTFREQ=$(echo "scale=1 ; $OUTFREQ/10" | bc)
> > > > > echo "Output Frequency
> "$OUTFREQ >>
> > > > > $OUT.tmp
> > > > > OUTAMPS=$(echo "scale=1 ; $OUTAMPS/10" | bc)
> > > > > echo "Output Current
> "$OUTAMPS >>
> > > > > $OUT.tmp
> > > > > OUTLOAD=$(echo $OUTLOAD | sed 's/[ \t]*//')
> > > > > echo "Output Load
> "$OUTLOAD % >>
> > > > > $OUT.tmp
> > > > > echo >> $OUT.final
> > > > > cat $OUT.warn >> $OUT.final
> > > > > cat $OUT.tmp >> $OUT.final
> > > > > echo '<FONT COLOR="Black">' >> $OUT.final
> > > > > echo "Load=$OUTLOAD" >> $OUT.final
> > > > > echo "Charge=$BATTERY_LEVEL" >> $OUT.final
> > > > > echo '</FONT>' >> $OUT.final
> > > > > rm $OUT.tmp
> > > > > rm $OUT.warn
> > > > > esac
> > > > > else
> > > > > echo "Device Unreachable!" >> $OUT.final
> > > > > #COLOUR=yellow
> > > > > fi
> > > > > $BB $BBDISP "status $UPSNAME.ups $COLOUR $DATE $(cat
> $OUT.final)"
> > > > > rm $OUT.final
> > > > > done
> > > > >
> > > > > --- snip ---
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > > > >
> > >
> ------------------------------------------------------------------------
> > > > > *From:* thorsten.erdmann at daimler.com
> > > > > [mailto:thorsten.erdmann at daimler.com]
> > > > > *Sent:* Thursday, 10 September 2009 2:18 PM
> > > > > *To:* hobbit at hswn.dk
> > > > > *Subject:* [hobbit] Antwort: RE: [hobbit] UPS monitoring using
> devmon
> > > > >
> > > > >
> > > > > Hi Craig,
> > > > > hi David,
> > > > >
> > > > > sounds very nice.
> > > > >
> > > > > I tried that snmpwalk. It only works with snmp V1. This is the
> output:
> > > > >
> > > > > SNMPv2-SMI::mib-2.33.1.1.1.0 = STRING: "MGE UPS SYSTEMS"
> > > > > SNMPv2-SMI::mib-2.33.1.1.2.0 = STRING: "Galaxy PW Single//"
> > > > > SNMPv2-SMI::mib-2.33.1.1.3.0 = ""
> > > > > SNMPv2-SMI::mib-2.33.1.1.4.0 = STRING: "GB (SN 49EE49044)"
> > > > > SNMPv2-SMI::mib-2.33.1.1.5.0 = ""
> > > > > SNMPv2-SMI::mib-2.33.1.1.6.0 = ""
> > > > >
> > > > > As I see it, this is only the description of the UPS. I will
> look for
> > > > > the MIB of my devices.
> > > > > Don't know where all the other things which I want to monitor at
> > > > > minimum are located in the MIB like:
> > > > >
> > > > > Overall status or am I runnung on battery
> > > > > output power
> > > > > remaining battery time
> > > > > temperature
> > > > >
> > > > > > I'll look at uploading it to the SF repository.
> > > > > Maybe this is a stupid question, but I don't find templates
> and things
> > > > > on the SF page. Only devmon itself.
> > > > > I look at http://devmon.sourceforge.net/ and at
> > > > > http://sourceforge.net/projects/devmon/
> > > > > There is a devmon-template file there, but as I see it, it
> contains
> > > > > only the templates which are delivered with devmon itself.
> > > > >
> > > > > It would be nice if you share your templates. You can also
> contact me
> > > > > via EMail at thorsten.erdmann at daimler dot com
> > > > >
> > > > > Thank you very much
> > > > >
> > > > > Thorsten
> > > > >
> > > > >
> > > > >
> > > > > >
> > > > > > Craig
> > > > > >
> > > > > > -----Original Message-----
> > > > > > From: David Baldwin [mailto:david.baldwin at ausport.gov.au]
> > > > > > Sent: Thursday, 10 September 2009 11:53 AM
> > > > > > To: hobbit at hswn.dk
> > > > > > Subject: Re: [hobbit] UPS monitoring using devmon
> > > > > >
> > > > > > thorsten.erdmann at daimler.com wrote:
> > > > > > >
> > > > > > > Hi,
> > > > > > >
> > > > > > > sorry if this a little offtopic, but maybe someone has a
> devmon
> > > > > > > template for the following UPS:
> > > > > > >
> > > > > > > Emerson/Liebert HiPulse MM
> > > > > > > MGE Galaxy Single
> > > > > > > MGE Upsilon STS_100 Cross switch
> > > > > > > MGE Upsilon STS_20 Cross switch
> > > > > > >
> > > > > > > Thank you
> > > > > > > Thorsten
> > > > > > >
> > > > > > >
> > > > > > > If you are not the intended addressee, please inform us
> > > immediately
> > > > > > > that you have received this e-mail in error, and delete it. We
> > > thank
> > > > > > > you for your cooperation.
> > > > > > >
> > > > > > I have a template for the standard UPS MIB which I could send
> > > through. I
> > > > > > have a little more work to do on it splitting the power status
> > > into 3
> > > > > > tests for input, output and battery. Should give me
> motivation to
> > > > > > complete this today and I will upload to devmon SF site.
> > > > > >
> > > > > > You can check if your UPS supports the standard UPS MIB or
> wants a
> > > > > > proprietary one (substituting for myups below, and your
> > > community string
> > > > > > if it is not "public"):
> > > > > >
> > > > > > snmpwalk -v2c -cpublic myups 1.3.6.1.2.1.33.1.1
> > > > > >
> > > > > > Note that some UPS devices only support SNMPv1, so try -v1
> > > instead of
> > > > > > -v2c above if it doesn't work.
> > > > > >
> > > > > > David.
> > > > > >
> > > > > > --
> > > > > > David Baldwin - IT Unit
> > > > > > Australian Sports Commission www.ausport.gov.au
> > > > > > Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen
> ACT 2616
> > > > > > david.baldwin at ausport.gov.au Leverrier Street Bruce ACT
> > > 2617
> > > > > >
> > > > > >
> > > > > >
> > >
> ------------------------------------------------------------------------
> > > > > > -------------
> > > > > > Keep up to date with what's happening in Australian sport visit
> > > > > > http://www.ausport.gov.au
> > > > > >
> > > > > > This message is intended for the addressee named and may contain
> > > > > > confidential and privileged information. If you are not the
> intended
> > > > > > recipient please note that any form of distribution, copying or
> > > use of
> > > > > > this communication or the information in it is strictly
> > > prohibited and
> > > > > > may be unlawful. If you receive this message in error, please
> > > delete it
> > > > > > and notify the sender.
> > > > > >
> > >
> ------------------------------------------------------------------------
> > > > > > -------------
> > > > > >
> > > > > > To unsubscribe from the hobbit list, send an e-mail to
> > > > > > hobbit-unsubscribe at hswn.dk
> > > > > >
> > > > > >
> > > > > > DISCLAIMER:
> > > > > >
> > > > > >
> > > > > > The information contained in this email message is
> confidential and
> > > > > > for the attention of the intended recipient only.
> > > > > > It is not necessarily the official view or communication of the
> > > > > > Rodney District Council.
> > > > > > If you are not the intended recipient you must not disclose,
> copy or
> > > > > > distribute this message or the information in it.
> > > > > > If you have received this message in error, please delete or
> destroy
> > > > > > all copies of the email and notify the sender immediately.
> > > > > > Rodney District Council accepts no responsibility for any
> effects
> > > > > > this email message or attachments has on the recipient
> network or
> > > > > > computer system.
> > > > > >
> > > > > > To unsubscribe from the hobbit list, send an e-mail to
> > > > > > hobbit-unsubscribe at hswn.dk
> > > > > >
> > > > > >
> > > > >
> > > > > If you are not the intended addressee, please inform us
> immediately
> > > > > that you have received this e-mail in error, and delete it. We
> thank
> > > > > you for your cooperation.
> > > > >
> > > > > NOTICE: This email and any attachments are confidential.
> > > > > They may contain legally privileged information or
> > > > > copyright material. You must not read, copy, use or
> > > > > disclose them without authorisation. If you are not an
> > > > > intended recipient, please contact us at once by return
> > > > > email and then delete both messages and all attachments.
> > > > >
> > > > > NOTICE: This email and any attachments are confidential.
> > > > > They may contain legally privileged information or
> > > > > copyright material. You must not read, copy, use or
> > > > > disclose them without authorisation. If you are not an
> > > > > intended recipient, please contact us at once by return
> > > > > email and then delete both messages and all attachments.
> > > > >
> > > >
> > > >
> > > > --
> > > > David Baldwin - IT Unit
> > > > Australian Sports Commission www.ausport.gov.au
> > > > Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen ACT 2616
> > > > david.baldwin at ausport.gov.au Leverrier Street Bruce ACT
> 2617
> > > >
> > > >
> > > > To unsubscribe from the hobbit list, send an e-mail to
> > > > hobbit-unsubscribe at hswn.dk
> > > >
> > > >
> > >
> > > If you are not the intended addressee, please inform us immediately
> > > that you have received this e-mail in error, and delete it. We thank
> > > you for your cooperation.
> > >
> >
> >
> > --
> > David Baldwin - IT Unit
> > Australian Sports Commission www.ausport.gov.au
> > Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen ACT 2616
> > david.baldwin at ausport.gov.au Leverrier Street Bruce ACT 2617
> >
> >
> > To unsubscribe from the hobbit list, send an e-mail to
> > hobbit-unsubscribe at hswn.dk
> >
> >
>
> If you are not the intended addressee, please inform us immediately
> that you have received this e-mail in error, and delete it. We thank
> you for your cooperation.
>
More information about the Xymon
mailing list