[hobbit] Antwort: RE: [hobbit] UPS monitoring using devmon
David Baldwin
david.baldwin at ausport.gov.au
Thu Sep 10 09:51:49 CEST 2009
Sorry all, didn't get time today to update the UPS template today.
It has separate graphs for input voltage, output phase voltages, battery
levels and separate tests/alerting on various conditions - input
voltage=0, battery time remaining <15 mins, output phase overload, etc.
David.
> Oops, forgot to add the graphing bit.
>
> Usual stuff.
> In hobbitserver.cfg
> Add "ups=ncv" to TEST2RRD=
> Add "ups" to GRAPHS=
> Add line NCV_ups="Load:GAUGE,Charge:GAUGE"
>
> Add this to hobbitgraph.cfg
> [ups]
> TITLE UPS Charge
> YAXIS Power
> -u 100
> -l 0
> DEF:u=ups.rrd:Charge:AVERAGE
> DEF:p=ups.rrd:Load:AVERAGE
> LINE2:u#00CC00:Charge
> LINE2:p#0000FF:Load
> COMMENT:\n
> GPRINT:u:LAST:Charge \: %5.1lf%s (cur)
> GPRINT:u:MAX: \: %5.1lf%s (max)
> GPRINT:u:MIN: \: %5.1lf%s (min)
> GPRINT:u:AVERAGE: \: %5.1lf%s (avg)\n
> GPRINT:p:LAST:Load \: %5.1lf%s (cur)
> GPRINT:p:MAX: \: %5.1lf%s (max)
> GPRINT:p:MIN: \: %5.1lf%s (min)
> GPRINT:p:AVERAGE: \: %5.1lf%s (avg)\n
> Cheers
> Vernon
>
>
>
> ------------------------------------------------------------------------
> *From:* Everett, Vernon [mailto:Vernon.Everett at woodside.com.au]
> *Sent:* Thursday, 10 September 2009 2:50 PM
> *To:* 'hobbit at hswn.dk'
> *Subject:* RE: [hobbit] Antwort: RE: [hobbit] UPS monitoring using devmon
>
> I wrote this a while back for our MGEs.
> As you can see, it predates my introduction to devmon and indicates a
> complete lack of understanding of SNMP.
> That being said, the code and the MIBs might give you a good
> indication of where to start.
> (Either that, or you can just use it as "good enough")
> This was designed to run on the hobbit/xymon server.
>
> I have been meaning to rewrite this, or move it to devmon, but just
> haven't had the time.
> (And it's doing an adequate job for now.)
>
> Cheers
> V
>
> bb-host entries look like this
> 1.2.3.4 galaxy3000 # http://1.2.3.4/ups_prop.htm ups galaxy3000
> COMMENT:"Meaningful Comment if required"
> 2.3.4.5 Karratha_UPS # http://2.3.4.5/ups_prop.htm ups galaxy3000
> COMMENT:"Insert Comment"
>
>
>
>
> --- snip---
>
> cat ups.ksh
> #!/bin/ksh
> DATE=$(date)
> #set -x
> SPACER="
> "
> BBTMP=/tmp
> #BBHOSTS=/etc/hobbit/bb-hosts
> #OUT=$BBTMP/upspage
> BBHOSTLIST="$BBHOSTS $(grep ^include $BBHOSTS | awk '{ print $2 }')" #
> Make sure we read the include files too
> #grep -h " ups " $BBHOSTLIST | egrep -v "^page|^include"
> grep -h " ups " $BBHOSTLIST | egrep -v "^page|^include" | while read
> IP UPSNAME HASH URL UPS TYPE OTHER
> do
> echo $IP $UPSNAME
> ping -c1 $IP > /dev/null
> if [ $? -eq 0 ]
> then
> COLOUR=green
> case $TYPE in
> galaxy3000)
> > $OUT.warn
> > $OUT.tmp
> TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.1.0)
> DEVICE=${TEMP##*:} # String
> TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.2.0)
> MODEL=${TEMP##*:} # String
> TEMP=$(snmpget -v1 -c public $IP SNMPv2-MIB::sysLocation.0)
> LOCATION=${TEMP##*:} # String
> TEMP=$(snmpget -v1 -c public $IP SNMPv2-SMI::mib-2.33.1.1.4.0)
> SERIAL=${TEMP##*:} # String
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.4.8.0)
> LOWBATTERY=${TEMP##*:} # Integer % Point at
> which shutdown triggered
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.1.0)
> TIME_REMAIN=${TEMP##*:} # Integer seconds
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.2.0)
> BATTERY_LEVEL=${TEMP##*:} # Integer %
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.9.0)
> BATTERY_FAULT=${TEMP##*:} # Integer 1=yes 2=no
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.11.0)
> BATTERY_REPLACE=${TEMP##*:} # Integer 1=yes 2=no
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.5.15.0)
> CHARGER_FAULT=${TEMP##*:} # Integer 1=yes 2=no
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.3.0)
> OUT_ON_BAT=${TEMP##*:} # Integer 1=yes 2=no
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.4.0)
> OUT_ON_BYPASS=${TEMP##*:} # Integer 1=yes 2=no
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.10.0)
> OUT_OVERLOAD=${TEMP##*:} # Integer 1=yes 2=no
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.10.0)
> COMMSOK=${TEMP##*:} # Integer 1=yes 2=no
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.1.0)
> INPHASES=${TEMP##*:} # Integer 1 or 3
>
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.2.1.2)
> INVOLT=${TEMP##*:} # Integer 10ths of a volt
>
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.2.1.3)
> INFREQ=${TEMP##*:} # Integer 10ths of a Hertz
>
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.2.1.6)
> INAMPS=${TEMP##*:} # Integer 10ths of an Amp
>
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.3.0)
> INOK=${TEMP##*:} # Integer 1=yes 2=no
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.6.4.0)
> INFAILCAUSE=${TEMP##*:} # Integer 1=no fault
> # 2=bad voltage
> # 3=bad frequency
> # 4=no voltage
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.1.0)
> OUTPHASES=${TEMP##*:} # Integer 1 or 3
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.2)
> OUTVOLT=${TEMP##*:} # Integer 10ths of a volt
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.3)
> OUTFREQ=${TEMP##*:} # Integer 10ths of a Hertz
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.4)
> OUTLOAD=${TEMP##*:} # Integer %
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.2.1.5)
> OUTAMPS=${TEMP##*:} # Integer 10ths of an Amp
> TEMP=$(snmpget -v1 -c public $IP 1.3.6.1.4.1.705.1.7.11.0)
> OVERTEMP=${TEMP##*:} # Integer 1=yes 2=no
> echo "Manufacturer "$DEVICE | sed
> 's/"//g' >> $OUT.tmp
> echo "Model "$MODEL | sed
> 's/"//g' >> $OUT.tmp
> echo "Serial Number "$SERIAL | sed
> 's/"//g' >> $OUT.tmp
> echo "Location "$LOCATION |
> sed 's/"//g' >> $OUT.tmp
> echo >> $OUT.tmp
> #$LOWBATTERY
> #WARN=""
> #[ -z "$TIME_REMAIN" ] && TIME_REMAIN=0
> #[ $TIME_REMAIN -lt 1200 -a "$COLOUR" != "red" ] &&
> COLOUR=yellow
> #[ $TIME_REMAIN -lt 1200 ] && WARN="Time Remaining low"
> #[ $TIME_REMAIN -lt 600 ] && COLOUR=red
> #[ $TIME_REMAIN -lt 600 ] && WARN="Time Remaining critical"
> #[ "$WARN" != "" ] && echo $WARN >> $OUT.warn
> ((s=$TIME_REMAIN%60))
> ((m=$TIME_REMAIN/60))
> echo "Time Remaining "$m Minutes $s
> Seconds >> $OUT.tmp
> WARN=""
> [ -z "$BATTERY_LEVEL" ] && BATTERY_LEVEL=0
> [ $BATTERY_LEVEL -lt 95 -a "$COLOUR" != "red" ] &&
> COLOUR=yellow
> [ $BATTERY_LEVEL -lt 95 ] && WARN="Battery level low"
> [ $BATTERY_LEVEL -lt 50 ] && COLOUR=red
> [ $BATTERY_LEVEL -lt 50 ] && WARN="Battery level critical"
> [ "$WARN" != "" ] && echo $WARN >> $OUT.warn
> echo "Battery Level "$BATTERY_LEVEL
> % >> $OUT.tmp
> BATTERY_LEVEL=$(echo $BATTERY_LEVEL | sed 's/[ \t]*//')
> if [ $BATTERY_FAULT -eq 1 ]
> then
> BF=Yes
> COLOUR=red
> echo "Battery Fault!" >> $OUT.warn
> else
> BF=No
> fi
> echo "Battery Fault "$BF >> $OUT.tmp
> if [ $BATTERY_REPLACE -eq 1 ]
> then
> BR=Yes
> COLOUR=red
> echo "Battery replacement required" >> $OUT.warn
> else
> BR=No
> fi
> echo "Replace Battery "$BR >> $OUT.tmp
> if [ $BATTERY_FAULT -eq 1 ]
> then
> BR=Yes
> COLOUR=red
> echo "Battery replacement required" >> $OUT.warn
> else
> BR=No
> fi
> if [ $CHARGER_FAULT -eq 1 ]
> then
> CF=Yes
> COLOUR=red
> echo "Charger Fault" >> $OUT.warn
> else
> CF=No
> fi
> echo "Charger Fault "$CF >> $OUT.tmp
> if [ $OUT_ON_BAT -eq 1 ]
> then
> OUT_ON_BAT=Yes
> COLOUR=red
> echo "UPS running on battery" >> $OUT.warn
> else
> OUT_ON_BAT=No
> fi
> echo "On Battery "$OUT_ON_BAT
> >> $OUT.tmp
> if [ $OUT_ON_BYPASS -eq 1 ]
> then
> OUT_ON_BYPASS=Yes
> COLOUR=red
> echo "UPS on power bypass" >> $OUT.warn
> else
> OUT_ON_BYPASS=No
> fi
> echo "On Bypass
> "$OUT_ON_BYPASS >> $OUT.tmp
> if [ $OUT_OVERLOAD -eq 1 ]
> then
> OUT_OVERLOAD=Yes
> COLOUR=red
> echo "UPS output overload" >> $OUT.warn
> else
> OUT_OVERLOAD=No
> fi
> echo "Battery Overload "$OUT_OVERLOAD
> >> $OUT.tmp
> if [ $OVERTEMP -eq 1 ]
> then
> OVERTEMP=Yes
> COLOUR=red
> echo "Unit overheating" >> $OUT.warn
> else
> OVERTEMP=No
> fi
> echo "Unit Overheating "$OVERTEMP >>
> $OUT.tmp
> #if [ $COMMSOK -eq 2 ]
> #then
> # COMMSOK=No
> # COLOUR=red
> # echo "No comms from device" >> $OUT.warn
> #else
> # COMMSOK=Yes
> #fi
> #echo "Comms OK "$COMMSOK >>
> $OUT.tmp
> echo >> $OUT.tmp
> echo "Input Phases "$INPHASES >>
> $OUT.tmp
> INVOLT=$(echo "scale=1 ; $INVOLT/10" | bc)
> echo "Input Voltage "$INVOLT >>
> $OUT.tmp
> INFREQ=$(echo "scale=1 ; $INFREQ/10" | bc)
> echo "Input Frequency "$INFREQ >>
> $OUT.tmp
> INAMPS=$(echo "scale=1 ; $INAMPS/10" | bc)
> echo "Input Current "$INAMPS >>
> $OUT.tmp
> if [ $INOK -eq 1 ]
> then
> # A silly case of reverse logic applies here
> INOK=No
> COLOUR=red
> echo "Power input outside tollerance" >> $OUT.warn
> else
> INOK=Yes
> fi
> echo "Input OK "$INOK >> $OUT.tmp
> [ $INFAILCAUSE -eq 1 ] && FAILCAUSE="No failures"
> [ $INFAILCAUSE -eq 2 ] && FAILCAUSE="Voltage out of
> tollearance"
> [ $INFAILCAUSE -eq 3 ] && FAILCAUSE="Frequency out of
> tollernace"
> [ $INFAILCAUSE -eq 4 ] && FAILCAUSE="No voltage - power fail"
> echo "Cause of Failure "$FAILCAUSE >>
> $OUT.tmp
> echo >> $OUT.tmp
> echo "Output Phases "$OUTPHASES >>
> $OUT.tmp
> OUTVOLT=$(echo "scale=1 ; $OUTVOLT/10" | bc)
> echo "Output Voltage "$OUTVOLT >>
> $OUT.tmp
> OUTFREQ=$(echo "scale=1 ; $OUTFREQ/10" | bc)
> echo "Output Frequency "$OUTFREQ >>
> $OUT.tmp
> OUTAMPS=$(echo "scale=1 ; $OUTAMPS/10" | bc)
> echo "Output Current "$OUTAMPS >>
> $OUT.tmp
> OUTLOAD=$(echo $OUTLOAD | sed 's/[ \t]*//')
> echo "Output Load "$OUTLOAD % >>
> $OUT.tmp
> echo >> $OUT.final
> cat $OUT.warn >> $OUT.final
> cat $OUT.tmp >> $OUT.final
> echo '<FONT COLOR="Black">' >> $OUT.final
> echo "Load=$OUTLOAD" >> $OUT.final
> echo "Charge=$BATTERY_LEVEL" >> $OUT.final
> echo '</FONT>' >> $OUT.final
> rm $OUT.tmp
> rm $OUT.warn
> esac
> else
> echo "Device Unreachable!" >> $OUT.final
> #COLOUR=yellow
> fi
> $BB $BBDISP "status $UPSNAME.ups $COLOUR $DATE $(cat $OUT.final)"
> rm $OUT.final
> done
>
> --- snip ---
>
>
>
>
>
> ------------------------------------------------------------------------
> *From:* thorsten.erdmann at daimler.com
> [mailto:thorsten.erdmann at daimler.com]
> *Sent:* Thursday, 10 September 2009 2:18 PM
> *To:* hobbit at hswn.dk
> *Subject:* [hobbit] Antwort: RE: [hobbit] UPS monitoring using devmon
>
>
> Hi Craig,
> hi David,
>
> sounds very nice.
>
> I tried that snmpwalk. It only works with snmp V1. This is the output:
>
> SNMPv2-SMI::mib-2.33.1.1.1.0 = STRING: "MGE UPS SYSTEMS"
> SNMPv2-SMI::mib-2.33.1.1.2.0 = STRING: "Galaxy PW Single//"
> SNMPv2-SMI::mib-2.33.1.1.3.0 = ""
> SNMPv2-SMI::mib-2.33.1.1.4.0 = STRING: "GB (SN 49EE49044)"
> SNMPv2-SMI::mib-2.33.1.1.5.0 = ""
> SNMPv2-SMI::mib-2.33.1.1.6.0 = ""
>
> As I see it, this is only the description of the UPS. I will look for
> the MIB of my devices.
> Don't know where all the other things which I want to monitor at
> minimum are located in the MIB like:
>
> Overall status or am I runnung on battery
> output power
> remaining battery time
> temperature
>
> > I'll look at uploading it to the SF repository.
> Maybe this is a stupid question, but I don't find templates and things
> on the SF page. Only devmon itself.
> I look at http://devmon.sourceforge.net/ and at
> http://sourceforge.net/projects/devmon/
> There is a devmon-template file there, but as I see it, it contains
> only the templates which are delivered with devmon itself.
>
> It would be nice if you share your templates. You can also contact me
> via EMail at thorsten.erdmann at daimler dot com
>
> Thank you very much
>
> Thorsten
>
>
>
> >
> > Craig
> >
> > -----Original Message-----
> > From: David Baldwin [mailto:david.baldwin at ausport.gov.au]
> > Sent: Thursday, 10 September 2009 11:53 AM
> > To: hobbit at hswn.dk
> > Subject: Re: [hobbit] UPS monitoring using devmon
> >
> > thorsten.erdmann at daimler.com wrote:
> > >
> > > Hi,
> > >
> > > sorry if this a little offtopic, but maybe someone has a devmon
> > > template for the following UPS:
> > >
> > > Emerson/Liebert HiPulse MM
> > > MGE Galaxy Single
> > > MGE Upsilon STS_100 Cross switch
> > > MGE Upsilon STS_20 Cross switch
> > >
> > > Thank you
> > > Thorsten
> > >
> > >
> > > If you are not the intended addressee, please inform us immediately
> > > that you have received this e-mail in error, and delete it. We thank
> > > you for your cooperation.
> > >
> > I have a template for the standard UPS MIB which I could send through. I
> > have a little more work to do on it splitting the power status into 3
> > tests for input, output and battery. Should give me motivation to
> > complete this today and I will upload to devmon SF site.
> >
> > You can check if your UPS supports the standard UPS MIB or wants a
> > proprietary one (substituting for myups below, and your community string
> > if it is not "public"):
> >
> > snmpwalk -v2c -cpublic myups 1.3.6.1.2.1.33.1.1
> >
> > Note that some UPS devices only support SNMPv1, so try -v1 instead of
> > -v2c above if it doesn't work.
> >
> > David.
> >
> > --
> > David Baldwin - IT Unit
> > Australian Sports Commission www.ausport.gov.au
> > Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen ACT 2616
> > david.baldwin at ausport.gov.au Leverrier Street Bruce ACT 2617
> >
> >
> > ------------------------------------------------------------------------
> > -------------
> > Keep up to date with what's happening in Australian sport visit
> > http://www.ausport.gov.au
> >
> > This message is intended for the addressee named and may contain
> > confidential and privileged information. If you are not the intended
> > recipient please note that any form of distribution, copying or use of
> > this communication or the information in it is strictly prohibited and
> > may be unlawful. If you receive this message in error, please delete it
> > and notify the sender.
> > ------------------------------------------------------------------------
> > -------------
> >
> > To unsubscribe from the hobbit list, send an e-mail to
> > hobbit-unsubscribe at hswn.dk
> >
> >
> > DISCLAIMER:
> >
> >
> > The information contained in this email message is confidential and
> > for the attention of the intended recipient only.
> > It is not necessarily the official view or communication of the
> > Rodney District Council.
> > If you are not the intended recipient you must not disclose, copy or
> > distribute this message or the information in it.
> > If you have received this message in error, please delete or destroy
> > all copies of the email and notify the sender immediately.
> > Rodney District Council accepts no responsibility for any effects
> > this email message or attachments has on the recipient network or
> > computer system.
> >
> > To unsubscribe from the hobbit list, send an e-mail to
> > hobbit-unsubscribe at hswn.dk
> >
> >
>
> If you are not the intended addressee, please inform us immediately
> that you have received this e-mail in error, and delete it. We thank
> you for your cooperation.
>
> NOTICE: This email and any attachments are confidential.
> They may contain legally privileged information or
> copyright material. You must not read, copy, use or
> disclose them without authorisation. If you are not an
> intended recipient, please contact us at once by return
> email and then delete both messages and all attachments.
>
> NOTICE: This email and any attachments are confidential.
> They may contain legally privileged information or
> copyright material. You must not read, copy, use or
> disclose them without authorisation. If you are not an
> intended recipient, please contact us at once by return
> email and then delete both messages and all attachments.
>
--
David Baldwin - IT Unit
Australian Sports Commission www.ausport.gov.au
Tel 02 62147830 Fax 02 62141830 PO Box 176 Belconnen ACT 2616
david.baldwin at ausport.gov.au Leverrier Street Bruce ACT 2617
More information about the Xymon
mailing list