Re: [xymon] ESX 4.1

[Thomas Eckert <thomas.eckert (at) IT-Eckert.de>]

As Vernon wrote to the list in reply to your post installing a
xymon-/hobbit-client on the ESX-host is not sufficient for monitoring
the ESX. The reason for this is
a) the service-console is just a VM by itself, so there is no way to
monitor the cpu- and memory-consumption of the "bare-metal"
b) the service-console will not be available in post v4.1 ESX-versions
(at least that's announced by VMware)

Personally I havn't looked into SNMP because I had several reports by
people running small to mid-sized ESX installations that it's both
unreliable and reporting incorrect values.

"Vmware-Monitor for Xmyon (VMX)" takes the offical approach recommended
by VMware (and is thus _fully_ supported and not in conflict with
support-contracts, ...): the virtual management assistant vMA (a
pre-built virtual machine with management-tools available from VMware):
	http://www.vmware.com/go/vma4
collects the data. Data-processing is done by a small daemon that
generates the status-messages for Xymon.
Super-short outline how to get your ESX-monitoring up and running with VMX:
1. fetch the vMA from VMware from above url and install it.
2. install a xymon-client on the vMA, rpm available from
	http://staff.telkomsa.net/packages/rhel5/xymon/x86_64/
3. install VMX on vMA (client-extension script) and on the xymon-server
(for data-processing and graphing)

In particular you do not have to install anything on the ESX-hosts.

For more details I've attached the VMX-documentation for your convenience.

All the best,

	Thomas

On 10/24/2010 10:06 PM, Dave Garaway wrote:
> Thanks for the reply. Is there any tricks to getting the client install and running on the ESX hosts?
> 
> 
> 
> ----- Original Message -----
> From: "Vernon Everett" <everett.vernon (at) gmail.com>
> To: xymon (at) xymon.com
> Sent: Sunday, October 24, 2010 6:34:32 PM
> Subject: Re: [xymon] ESX 4.1
> 
> Hi Dave 
> 
> This question pops up every few months or so. I even asked it myself once upon a time. 
> The short, but unfortunately incorrect answer is that you can install the Red Hat client in the service console. It is after all, a Linux variant. 
> However, this monitors only the service console, which is itself, only a VM, so it gives you almost nothing about the general health of the system as a whole. 
> 
> You can install the Xymon client into each VM, in which case, you simply use the appropriate client for the installed OS. But again, this will only give an indication of the health of the VM, not the entire host server. 
> 
> At one point, when called upon to monitor ESX, I started trying to do some interesting stuff with SNMP using Devmon, but I moved on to a different project, so I never completed it. 
> I did however post to the list what I had managed to do, and hoped somebody else would have picked up where I left off. As far as I am aware, nobody did. :-( 
> NOTE : I am more than happy to be proven wrong on this point. :-) 
> Scan the list for postings from me from about 12 to 18 months ago. It might come up with something which may prove useful. 
> 
> Unless somebody takes the time to come up with an ESX specific client, or does some magic with SNMP, your only hope is to install clients into every VM. 
> 
> Regards 
> Vernon 
> 
> 
> 
> On Sun, Oct 24, 2010 at 8:13 AM, Dave Garaway < dave (at) dgaraway.com > wrote: 
> 
> 
> 
> 
> Does anyone have a good way to monitor ESX hosts and the VMs that are running on them? 
> 
> 
> To unsubscribe from the xymon list, send an e-mail to
> xymon-unsubscribe (at) xymon.com
> 
> 

-- 
-- --------------------------------------------------------------------
| IT-Beratung Eckert | Hartkirchweg 54      | fon: +49 (0)761/ 594 9898
| Thomas Eckert      | 79111 Freiburg i.Br. | fax: +49 (0)761/ 594 9899
|                    | Germany              | http://www.it-eckert.de/