FW: After IP server change bbcombotest is looking for the old IP address

[Bart Gillis]

Hi again,

 

I performed a grep on the server directory looking for the old IP address and found that this was hard coded in the compiled binaries.

So I’ve recompiled the hobbit source using the same Makefile (In which I changed the IP address on the line “BBHOSTIP = 10.0.6.13”)

 

After a make and a make install command my combo test is working.

 

I’ve however another problem.

I tried out the example:

WebCluster.http = (Web1.http || Web2.http) 

AppSrvCluster.procs = (AppSrv1.conn && AppSrv1.procs) || (AppSrv2.conn && AppSrv2.procs) 

Customer.cluster = WebCluster.http && AppSrvCluster.procs

 

My code is:

DC.svcs = (MSCT\-DC\-01.conn || MSCT\-DC\-02.conn)

DNS.svcs = (MSCT\-DC\-01.svcs || MSCT\-DC\-02.svcs)

CTCS.svcs = DC.svcs && DNS.svcs

 

DC is a connectivity check on 2 servers. (Primary and backup domain controllers)

DNS is the DNS services on the same servers.

 

On my bbhost config page I’ve configured

127.0.0.1             DC

127.0.0.1             DNS

127.0.0.1             CTCS

To get my combo test being displayed.

 

For DC and DNS the result is OK

(MSCT\-DC\-01.conn||MSCT\-DC\-02.conn) = (1||1) = 1

 MSCT-DC-01.conn

 MSCT-DC-02.conn

 

And 

(MSCT\-DC\-01.svcs||MSCT\-DC\-02.svcs) = (1||1) = 1

 MSCT-DC-01.svcs

 MSCT-DC-02.svcs

 

For CTCS I get:

DC.svcs&&DNS.svcs = -1&&-1 = 1

&unknown DC.svcs

&unknown DNS.svcs

 

Why do I get an unknown status????

 

Best regards

Bart Gillis

 

From: Bart Gillis 
Sent: donderdag 3 april 2008 13:58
To: hobbit at hswn.dk
Subject: After IP server change bbcombotest is looking for the old IP address

 

Hi,

I've set up a hobbit server very successfully with IP address 10.20.4.123. I became a FAN of this monitoring server.
But I still have one problem.

We changed our IP range, so I had to change the IP address of the Hobbit server. (10.0.6.13)
I was able to adjust all required setting. All test besides the Combotest are working fine now.

When I launch the combotest command from the console it still wants to connect to the old IP address

MMS-test:/opt/mms/server/bin # ./bbcombotest --debug
2008-04-03 13:45:58 Transport setup is:
2008-04-03 13:45:58 bbdportnumber = 1984
2008-04-03 13:45:58 bbdispproxyhost = NONE
2008-04-03 13:45:58 bbdispproxyport = 0
2008-04-03 13:45:58 Recipient listed as '10.20.4.123'
2008-04-03 13:45:58 Standard BB protocol on port 1984
2008-04-03 13:45:58 Will connect to address 10.20.4.123 port 1984
2008-04-03 13:46:01 Connect status is 113
2008-04-03 13:46:01 Could not connect to bbd at 10.20.4.123:1984 - No route to host
2008-04-03 13:46:01 Whoops ! bb failed to send message - Connection failed
2008-04-03 13:46:01 Symbolic '(B32910.mimix&&B32903.mimix)' converted to '(1&&1)                                      '
2008-04-03 13:46:01 Adding to combo msg: status COMBO.mimix green Thu Apr  3                                       13:45:58 2008
2008-04-03 13:46:01 Flushing combo message
      status COMBO.mimix green Thu Apr  3 13:45:58 2008
2008-04-03 13:46:01 Recipient listed as '10.20.4.123'
2008-04-03 13:46:01 Standard BB protocol on port 1984
2008-04-03 13:46:01 Will connect to address 10.20.4.123 port 1984
2008-04-03 13:46:04 Connect status is 113
2008-04-03 13:46:04 Could not connect to bbd at 10.20.4.123:1984 - No route to host
2008-04-03 13:46:04 Whoops ! bb failed to send message - Connection failed
2008-04-03 13:46:04 1 status messages merged into 2 transmissions


Where is the bbcombotest looking for that old IP address?
Haw can I change this behaviour?

Best regards

Bart Gillis 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.xymon.com/pipermail/xymon/attachments/20080404/71c4b2e2/attachment.html>